my friend is using the imagesetter fuji pi-m 1800 with quite some time
now the rip software is broken (using mac)
can anyone please tell me if i want to migrate to pc rip
what rip software i have to used with
sorry for my poor english
thx b4
my friend is using the imagesetter fuji pi-m 1800 with quite some time
now the rip software is broken (using mac)
can anyone please tell me if i want to migrate to pc rip
what rip software i have to used with
sorry for my poor english
thx b4
Have u PELBOX connection or SCSI-Pelbox connection?
Which RIP u have now on mac?
I need this info for good answer.
Greetings!
If u have newer version os SCSI PROM on Fuji motherboard, then, u need just Adaptec AHA 2940 SCSI Card, then replace original Windows SCSI driver with special version of this driver. I can send it.
I have all other driver. Its like ECRM Mako 4600.
But, if u have older version of SCSI PROM on motherboard (1.11), u must stay on mac (ADAPTEC AVA 2906 or older NCR integrated SCSI Card - Gray Mac)
Tell me for more.
@arsenlupin
we currently using pelbox - scsi with my old pc (os windows 3.11) + ecrm rip
and the ripping process very slow with it
i want to try using xitron navigator so i can install it with a new computer to make the ripping process faster
thx in advance for your help
Mik,
open SCSI Pelbox, then look at the PROMs. If su see version 1.11, u MUST use MAC.
If u want use PC, u have to change/copy this PROMS.
But, i can u send MAC Harlequin RIP version 5.3 or 5.5. It is very fast if u find Macintosh G4 with ADAPTEC AVA 2906 SCSI CARD. (Look at e-bay).
Make mne photo of all your parts (open imagsetter then make photo, SCSI BOX, CABLE), then send to me. It is simple. I make u right answer.
Greetings.
@arsenlupin
as i already told u that we used pc for running the rip (win 3.11)
now i want to try using a better computer n better os
e.g windows xp with navigator
i had navigator already (download from this forum)
what i want to know is there anything else i need (what plugins driver, etc ...)
best regards
I try to explain:
if u have SCSI Pelbox, u need just ecrm mako 4600 plugin driver for Xitron Navigator RIP, then set your imagsetter for SERIAL communication.
If u have just Pelbox (u say u have pelbox), u need special interface.
If u have integrated SCSI pelbox (open imagesetter to check it) i must see which PROm version u have.
If i see this, i send u driver&plug-in combination for u.
ok. We find right answer for u :)
Your ad here
http://www.megaupload.com/?d=JZXVY7V3
Run Setup, install downloaded ECRM RIP, select Mako 4600 (Fuji PI-M1800).
After installation, make restart, then move ecmrip5.3/sw/devices/*.i32 to x:/xitron/Navigator8.1/sw/devices.
yes !!!!
i'm gonna give it a try to do my best
thx a lot
Ask again if needed.
18 years experience with ECRM :)
would u verified my steps and corrected it
1. install xitron nav (device driver / plugins set to none or ???)
2. install ecrmrip from u (does it need a crack or something)
3. select mako 4600
4. restart
5. copy the device from ecrmrip to xitron
6. restart
7. proceed with xitron navigator
8. thx very much for your patience with me sir![]()
By the way ECRM RIP has Harlequin core like Xitron Navigator. So you can use it one if versions are same (there is v.7.x and v.8.x ECRM RIPs availible on this forum and "medicine" from Xitron (not patch lic only) have to work with them both
Availible w\o 3 & 4![]()
Bookmarks