+ Reply to Thread
Page 13 of 15 FirstFirst ... 3 11 12 13 14 15 LastLast
Results 181 to 195 of 222

Thread: Big Prinect 2010 Thread

  1. #181
    Donor eflatun is on a distinguished road
    Join Date
    Jan 2011
    Posts
    13
    Thanks
    12
    Thanked 4 Times in 4 Posts
    If you want to do lineraziton of your film/plate, you don't have to print via calibration manager. Just send a job which includes 5%,10%,20%,.....90%,95%. screen area patches and expose this job while linerazition and process calibration are deactivated under output parameter set. So your job will be exposed without any correction curve. Measure all patches, create a new lineraziton curve and enter measured results to this curve. Then activate this curve under output parameter set. That is all for linerazition.
    And it is similar procedure for any kind of RIP.

    Good luck
    Eflatun

  2. #182
    V-P
    V-P is offline
    Donor V-P is on a distinguished road
    Join Date
    Jan 2012
    Posts
    13
    Thanks
    4
    Thanked 1 Time in 1 Post
    Thnx Eflatun !

    I know about linearization now. I have another question:

    Why is there linearization & calibration ?

    Will it be enough to do just linearization or calibration is necessary ?

    thnx for reading...

  3. #183
    Banned boris_krotov will become famous soon enough
    Join Date
    Jan 2011
    Posts
    88
    Thanks
    33
    Thanked 58 Times in 17 Posts
    and what about Sherlock with database? Upload, please, if somebody have this software

  4. #184
    Donor T. Schruda is on a distinguished road
    Join Date
    Jan 2011
    Posts
    278
    Thanks
    11
    Thanked 27 Times in 18 Posts

    PM and heidelberg

    is there a chance to use the color toolbox to make a multichannel ICC profile with a chart generated by profile maker? i dont like the limited PM seperation possibilities..

    thanx

  5. #185
    Donor eflatun is on a distinguished road
    Join Date
    Jan 2011
    Posts
    13
    Thanks
    12
    Thanked 4 Times in 4 Posts
    Quote Originally Posted by V-P View Post
    Thnx Eflatun !

    I know about linearization now. I have another question:

    Why is there linearization & calibration ?

    Will it be enough to do just linearization or calibration is necessary ?

    thnx for reading...

    It depends on your system and aim. Four possibility; no curve, just lineraziton, just process calibration or both linerazition and process calibration curves. In most case I would suggest to apply just process calibration curves. But in some cases linearizition+process calibration must be used together. If providing standart dot gain values is not your aim then use just linerazition or no curve.

  6. #186
    V-P
    V-P is offline
    Donor V-P is on a distinguished road
    Join Date
    Jan 2012
    Posts
    13
    Thanks
    4
    Thanked 1 Time in 1 Post
    Quote Originally Posted by eflatun View Post
    It depends on your system and aim. Four possibility; no curve, just lineraziton, just process calibration or both linerazition and process calibration curves. In most case I would suggest to apply just process calibration curves. But in some cases linearizition+process calibration must be used together. If providing standart dot gain values is not your aim then use just linerazition or no curve.
    I tried the "Only proces calibration" but the result was worse.
    I think my main problem is that I am not getting the right values for solids.
    From what I know, normal values for DI are Y=1, Bk=1.8 , C&M = 1.4
    What I read from densitometer is: Y=0.9, Bk=1.3, C&M=0.9

    Now my question is: How do I do it from the MetaDimensionRIP, so that when I print, I get the right solids without me twisting the ink keys every time ?

    Thnx for helping...

  7. #187
    Moderator babajingjumong is a jewel in the rough babajingjumong is a jewel in the rough babajingjumong is a jewel in the rough babajingjumong is a jewel in the rough babajingjumong's Avatar
    Join Date
    Aug 2011
    Posts
    315
    Thanks
    51
    Thanked 316 Times in 139 Posts

    Need expert advice...Print Prinect Interface

    hi, somebody tell and give an advice how to use the standard procedure for Print Prinect Interface and how to troubleshoot it in the Press Machine,..I tested it yesterday in SM74, i have a ppf file converted and save it in the Linear Flash Card and transferred it to the SM74 machine by OmniCard,.

    My problem is the output of the SM74 machine is not quiet compensated regarding to the original file percentages, is there any suggestions of how to troubleshoot it to the setting of machines..or to the Prinect Software? Sometimes the output of ink key setting is good but later on it produce bad output.

    is there a other setting regarding in coated and uncoated profile?
    do i need to create a new profile for that setting?
    need some expert advice...thank you.

    God Bless
    "People with a good Heart...is a good Person...God Bless"

  8. #188
    Donor amp080 is on a distinguished road
    Join Date
    Nov 2011
    Posts
    17
    Thanks
    0
    Thanked 4 Times in 3 Posts
    Quote Originally Posted by babajingjumong View Post
    hi, somebody tell and give an advice how to use the standard procedure for Print Prinect Interface and how to troubleshoot it in the Press Machine,..I tested it yesterday in SM74, i have a ppf file converted and save it in the Linear Flash Card and transferred it to the SM74 machine by OmniCard,.

    My problem is the output of the SM74 machine is not quiet compensated regarding to the original file percentages, is there any suggestions of how to troubleshoot it to the setting of machines..or to the Prinect Software? Sometimes the output of ink key setting is good but later on it produce bad output.

    is there a other setting regarding in coated and uncoated profile?
    do i need to create a new profile for that setting?
    need some expert advice...thank you.

    God Bless

    Hi there have a look at http://www.excourse.com/presspercent/ there you should find a user guide to guide you better as regards to presspercent maybe you get an idea from where to start as regards tuning and setting up the key values. Personally i still have to set up PPI and start to use it hope it won't be hard to use since currently i am using presspercent and it's quite a straight forward app. Regarding profile...yes as far as i know different type of paper need different ink density (i mean coated matt,coated gloss and uncoated) so yes you should have a setup for each specific one. Also attached pls find flint group ink density's to guide you better
    Attached Images

  9. The Following User Says Thank You to amp080 For This Useful Post:

  10. #189
    Donor Figaro is on a distinguished road
    Join Date
    Nov 2011
    Posts
    7
    Thanks
    0
    Thanked 10 Times in 1 Post

    Please refer to Prinance 4.71

    Help!!
    Please refer to Prinance 4.71

    Prinance.part08.rar (200 MB)

  11. #190
    Moderator babajingjumong is a jewel in the rough babajingjumong is a jewel in the rough babajingjumong is a jewel in the rough babajingjumong is a jewel in the rough babajingjumong's Avatar
    Join Date
    Aug 2011
    Posts
    315
    Thanks
    51
    Thanked 316 Times in 139 Posts

    hi brother

    Quote Originally Posted by amp080 View Post
    Hi there have a look at http://www.excourse.com/presspercent/ there you should find a user guide to guide you better as regards to presspercent maybe you get an idea from where to start as regards tuning and setting up the key values. Personally i still have to set up PPI and start to use it hope it won't be hard to use since currently i am using presspercent and it's quite a straight forward app. Regarding profile...yes as far as i know different type of paper need different ink density (i mean coated matt,coated gloss and uncoated) so yes you should have a setup for each specific one. Also attached pls find flint group ink density's to guide you better

    one thing more brother, did you setup or create profile one by one? do i need to create curves or dgt? what is the procedure to do that? did you know the presetting the profile in PPI? or should i create it or input in the RIP software? before i will produce it on PPI?

    thank you again..

    God Bless
    "People with a good Heart...is a good Person...God Bless"

  12. Your ad here

  13. #191
    Member Hero_star will become famous soon enough
    Join Date
    Nov 2010
    Posts
    60
    Thanks
    41
    Thanked 77 Times in 18 Posts

    Post link again

    Quote Originally Posted by dzianis.puhach View Post
    Before LicensingSetup you need install HDEnvironmentSetup.

    Code:
    Only the registered members can see the download links/content. please Register to gain full access.
    link megaupload dead, can you post again other links, thanks
    further, i also found HDEnvironmentSetup.exe having Prinect Licensing file folder in prinect Signa station 2011 iso disk. download at link:
    Code:
    Only the registered members can see the download links/content. please Register to gain full access.
    posted by mzbdn
    Last edited by Hero_star; 03-10-2012 at 12:56 AM.

  14. #192
    Donor zooz82 will become famous soon enough
    Join Date
    Dec 2010
    Posts
    69
    Thanks
    48
    Thanked 44 Times in 15 Posts

    Pre press

    Hi please help..
    is there anyone have pre press interface 2011

    thanks

  15. #193
    Banned emulator has a spectacular aura about emulator has a spectacular aura about emulator has a spectacular aura about
    Join Date
    Nov 2010
    Posts
    152
    Thanks
    8
    Thanked 270 Times in 56 Posts
    could somebody reup the files and crack?
    my computer was crash down yesterday. i need those ff including the crack.

    metadimension, pdf toolbox and signastaion.

    thanks in advance. I hope somebody can help. really badly needed.

    -Emulator

  16. #194
    Member Hero_star will become famous soon enough
    Join Date
    Nov 2010
    Posts
    60
    Thanks
    41
    Thanked 77 Times in 18 Posts

    link crack printnect 2010,2011

    Quote Originally Posted by emulator View Post
    could somebody reup the files and crack?
    my computer was crash down yesterday. i need those ff including the crack.

    metadimension, pdf toolbox and signastaion.

    thanks in advance. I hope somebody can help. really badly needed.

    -Emulator
    Hi Emulator, link crack prinect 2010, 2011 include HDenvironmentSetup here:
    Code:
    Only the registered members can see the download links/content. please Register to gain full access.
    cracked provided by mzbdn, slivefox and printroot.

  17. The Following 3 Users Say Thank You to Hero_star For This Useful Post:

  18. #195
    PRC Member mazengh is on a distinguished road
    Join Date
    Feb 2011
    Posts
    58
    Thanks
    0
    Thanked 12 Times in 9 Posts
    Quote Originally Posted by T. Schruda View Post
    is there a chance to use the color toolbox to make a multichannel ICC profile with a chart generated by profile maker? i dont like the limited PM seperation possibilities..

    thanx
    this is implemented in color toolbox 2011

+ Reply to Thread
Page 13 of 15 FirstFirst ... 3 11 12 13 14 15 LastLast

Similar Threads

  1. I need Prinect Prepress Interface 2010
    By signastation in forum Requests
    Replies: 2
    Last Post: 02-05-2013, 06:05 AM
  2. Prinect all keys 2010 version
    By RicardoNit in forum Full Software
    Replies: 3
    Last Post: 07-03-2011, 07:12 PM
  3. Prinect Package Designer 2010
    By mydjf in forum Full Software
    Replies: 14
    Last Post: 04-21-2011, 05:19 PM
  4. Digital Printing Thread
    By Xin in forum Forum Suggestions & Feedback
    Replies: 1
    Last Post: 04-06-2011, 01:23 AM
  5. Prinect 2010
    By france in forum Requests
    Replies: 8
    Last Post: 03-23-2011, 04:00 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts